9130

DC-250kHz Switch-Mode Amplifier Power System

9130

10 kW, up to 180A continuous

Key Performance Capabilities:

Bandwidth: DC to 250 kHz
Minimum Drop/Rise Time: 7µs
Slew Rate: Up to 150 V/µs
Max Voltage: 0 to 200 Vp
Max Current: Up to 140 Ap / 180A RMS
Distortion: <0.1% at 1 kHz below clip
Max Long-Term Power: 10 kW*
Typical Output Ripple: 0.6V RMS
Power Factor: Typically 95% or greater

*At mains power below 208VAC, 30A maximum power will be reduced.

SKU: N/A Categories: Amplifiers, Standards

Request a Quote

Ask a Question

OVERVIEW

The 9130 is a powerful and flexible amplifier power system when the environment is difficult or existing AC Mains options are limited. This cabinet-based model, comprised of two 9115 units, can be powered from a variety of three-phase voltages from 200VAC to 415VAC*. It is power-efficient, with a typical efficiency over 90% at full power.

This combination of features makes the 9130 an ideal solution for a wide range of high-current, low-voltage applications that require both wide bandwidth and the ability to drive reactive or widely varying load impedances.

Stable when driving highly capacitive loads
Four-quadrant operation
User-selectable gain
User-selectable current limit to protect fragile DUTs or where specified in the Standard
DC enabled or DC blocked and DC Servo (for driving transformer-coupled loads or coils)
Balanced and/or unbalanced input
Operate as a voltage-controlled voltage source or voltage-controlled current source
Variable output impedance from 0 to 1 ohm (Voltage mode)

* Three-phase voltages above 240VAC will require a 5-wire service.

OUTPUT CHART

Output

	CONTINUOUS OUTPUT CURRENT
	9105	9110	9115	9130	9145	9160	9175	9190
13.5 VDC	35A	60A	90A	180A	270A	360A	450A	540A
24 VDC	35A	60A	90A	180A	270A	360A	450A	540A
48 VDC	34A	60A	90A	180A	270A	360A	450A	540A
30 VAC	35A	70A	90A	180A	270A	360A	450A	540A
60 VAC	35A	70A	80A	160A	240A	320A	400A	480A
120 VAC	35A	37A	37A	74A	100A	137A	174A	200A

Note: Performance data is for a purely resistive load; performance will be improved into loads that are partially or completely reactive.

PERFORMANCE

SPECIFICATIONS

Performance Specifications

Operating Modes: AC, DC, and AC + DC
Frequency, AC Mode Output (-3 dB): DC – 250 kHz
Max Voltage Ranges (no load),
- AC: 0 – 140 V_RMS
- AC + DC: 0 – ±200 V_P
Maximum Continuous Output Current: 180_RMS AC or DC
Power: 10 kW
Supply Voltage: Universal power supply with PFC, three-phase, 200V to 415VAC* ±10%, 30A, 50/60 Hz
Load Regulation (ref to full scale): <0.05%, DC to 100 Hz; <0.1%, 10 Hz to 10 kHz
Line Regulation (full scale): 100V to 250V AC_RMS
Harmonic Distortion,
- 80 kHz, Low-passed: Less than 0.3% from 10 Hz to 30 kHz; 0.5% up to 50 kHz
- 30 kHz, Low-passed: Less than 0.1% from 10 Hz to 50 kHz
Quiescent Power,
- Standby: 110W
- Run: 510W
DC Offset: <2 mV
Distortion: <1.0%
THD: .02% at 1kHz
Voltage Slew Rate, 8Ω: 150V per µs
Voltage Ripple: 250mV @ 250kHz
Efficiency: 85%, typical
Power Factor: .98, typical
Source Impedance: 5 mΩ + 6 µH
Cooling: Internal forced-air fans
Protection: Over/under voltage, over current, over temperature
Input, Signal In: BNC connector (unbalanced)
Output: High-current barrier strip

* Three-phase voltages above 240VAC will require a 5-wire service.

Operating Environment

Temperature: 5°C to 50°C (41°F to 122°F);
Maximum output power de-rated above 30°C (86°F)
Humidity: Maximum relative humidity 80% for temperatures up to 31°C decreasing linearly to 50% relative humidity at 40°C
Altitude: 3000 m Maximum
Environment: Indoor Use Only, Pollution degree 2
Equipment Class: Group 1 Class A
Transient Overvoltage: Overvoltage Category II
Dimensions (HxWxD): 35.05 x 22.56 x 31.56 in. (89.03 x 57.3 x 80.16 cm)
Weight (Approx.): 222 lbs. (100.7 kg)